2021 Cross Wrap DW 1400 Bale opener / Dewiring line

Technical data on the used bale feed conveyor: Manufacturer Bollegraaf Recycling Solutions B.V. Type HBT 1400/1200 * 12500 - 0° (chain belt conveyor) Overhaul of the conveyor belt in 2021 Operating hours after overhaul approx. 2 hours Effective width 1200 mm Belt length 10,150 mm Drive power 3 kW, the belt speed of the motor can be regulated via a frequency converter Belt speed 1.6 - 5.5 m/minute Belt type 250/2, 3+1, thickness 6.1 mm, the belt is without carrier Remark: The bale feed conveyor (chain belt conveyor) is used. The original year of manufacture is not known. The conveyor was overhauled in 2021. After the overhaul and assembly, the conveyor belt has only been in operation in set-up mode for approx. 2 hours. The infeed conveyor serves as a supply store for the bale opener and dewiring unit and can store bales over a length of 10 metres. The chain belt conveyor is controlled via the DW 1400 cross wrap dewiring unit. Whenever a bale is opened, dewired and fed to the feed hopper, a new bale is automatically fed from the feed belt. Technical data for the bale opener and dewiring unit: Manufacturer Cross Wrap OY Type DW 1400 dewiring unit Year of manufacture 2021 (new machine) Operating hours approx. 2 hours (exclusively set-up operation by the manufacturer Cross Wrap) Min./max. permitted bale dimensions: Height min. 700 mm, max. 1400 mm Width min. 700 mm, max. 1400 mm Length min. 1100 mm, max. 2500 mm Bale weights min. 250 kg, max. 2000 kg Bale materials Paper, cardboard, plastic films, plastics, pulp and various other recycling materials Throughput capacity up to 60 bales per hour, depending on material Remark: The bale opener and dewrapper is a new machine, built in 2021 and was operated exclusively by the manufacturer Cross Wrap for approx. 2 hours in set-up mode. The system works fully automatically. Bales are held on the infeed conveyor belt by two hydraulically operated grippers. The bale opener follows the contour of the bale and automatically cuts through the wrapping film and the steel or plastic bale wires with a hydraulically driven, rotating knife. The hydraulically driven gripper system holds the film with the steel or plastic bale wires and pulls them out sideways after the opening process. Finally, the wires and film are wound into small coils via a winding unit and ejected into a box via a side chute. Once the bale has been opened and the film and wire removed, it is discharged into the storage bunker with a dosing drum using a conveyor belt. It is then broken down into several pieces. Technical data for the ‘steel lamella conveyor’ (steel plate conveyor), feed hopper with dosing drum: Manufacturer Bollegraaf Recycling Solutions B.V. Type Drumfeeder BDF 1200/2000*11000 Year of construction 2014, overhauled in 2021 Operating hours after overhaul approx. 2 hours (set-up operation only) Drum width 2000 mm Drum diameter 1360 mm Drum drive power 15 kW Rotation speed 40 - 70 revolutions/minute, controlled via a frequency converter 12 carriers on the drum, 80 mm high, 2000 mm long Hardox ripper teeth, 48 pieces, 160 mm high Steel slat conveyor belt (steel plate conveyor) 6“ conveyor belt chain, breaking load 24,000 lbs Hopper volume approx. 10,000 x 2,000 x 2,500 mm = 50 m³ Transport dimensions 11,500 x 2,600 x 3,075 mm (l x w x h) Remark: The feed hopper with dosing drum (drumfeeder) is used, built in 2014 and was overhauled in 2021. After the overhaul and assembly, the conveyor belt has only been in operation for approx. 2 hours in set-up mode. We will not assume liability for the given technical data and possible errors!